The preparation technique is different and varies. Keurig Coffee maker has its own method to prepare coffee with the help of water filter attached in it. It is widely suggested that you use a water filter to enhance the quality and flavor of your beverages and protect your brewer from scale building caused by minerals in your water. If you detect unpleasant tastes, such as those caused by chlorine or other minerals, you should consider using a water filter.
Now the question arises, where is the Water Filter in the Keurig Coffee Maker? The Keurig features a water filter about 2 inches long and 1.125 inches tall, and it is housed inside a BPA-free plastic filter handle.
A water filter may be installed in the Keurig coffee brewer’s backwater reservoir. It employs charcoal water filters, a transparent plastic filter handle (usually supplied separately from the brewer), and a water tank positioned on the machine’s rear.
Replacing the Water Filter on a Brewer
After brewing roughly 1000 fluid ounces through your machine, you should replace the water filter on your Keurig Coffee Brewer. This is equivalent to 125 eight-ounce cups of coffee per two months. After replacing your Keurig water filter, you may use the touch screen on your brewer to set a water filter reminder.
How To Replace Keurig Water Filter
The purifying filter in your Keurig’s water reservoir is only meant to endure a certain number of brew cycles, not a specific amount of time. You should replace your Keurig less frequently if you use it less often.
According to Keurig, filters should be replaced every two months. If you don’t brew every day, though, it recommends changing the filter every 60 tank refills. You might also make it a habit to descale the Keurig every time you change the filter.
Some newer Keurig models let you set a water filter reminder, so you don’t have to guess when it’s time to replace the filter.
When the water filter is depleted, it no longer filters the water in the reservoir as effectively as it should. This will have an effect not only on the quality of the coffee, but also on how quickly particulates will accumulate inside the machine.
The smell of coffee from your Keurig may help you get out of bed each morning. But, just as your Keurig takes care of you, you must take care of it as well, or else the coffee it brews and the machine itself will degrade over time.
You should not only clean and descale your Keurig every three to six months, but you should also replace the water filter every few months. Here’s how to do it:
- Remove the Keurig water reservoir’s lid. The water reservoir is usually found on the left side of a Keurig machine. You may reach the water filter by completely removing the reservoir’s top. If there is water in the reservoir or if the reservoir is empty, you can change the filter.
- Remove the filter unit. The upper filter holder’s handle will protrude from the water reservoir. Take a tight grip on the handle and pull it out of the reservoir. The filter-holder unit’s underside will be secured into plastic grooves on the bottom of the water reservoir. To remove the filter-holder device, you may need to rock it back into position or give it a firm tug. If you have a Keurig Classic series, your filter will be black and have a circular timer on the end. The filter on a K200 Plus is clear and shorter, but filters on K300 and above versions are taller, skinny, and transparent.
- Remove the used filter from the filter holder. Pinch the tabs at the bottom of the filter unit with your thumb and index finger. Pull down to free the lower filter holder, then remove the old filter. The old filter may be discarded in the garbage bin in your kitchen.
How to Install a New Filter
- Get a new Keurig filter bundle. Keurig water filters are not offered separately, therefore you must purchase a set. They’re usually offered in packs of six or twelve. Keurig filters are available at the same places that sell Keurig units. Check any company or department store that sells housewares, such as Bed Bath & Beyond, Sears, Target, and bigger supermarkets.
- Soak the filter for 5 to 10 minutes in water. The filter must soak and absorb water before being installed in your Keurig and making the first cup of coffee. Fill a cup or bowl halfway with water, then place the filter in it. While the filter is soaking, make sure it is thoroughly immersed. After 10 minutes, the filter will have absorbed water and settled to the bottom of the cup or bowl.
- Rinse the filter thoroughly. After soaking, rinse the filter with tap water for the best results. Maintain a gentle flow of water while rinsing the filter for a full 60 seconds.
- Remove the lower filter holder and rinse it. The underside of the lower filter holder will have a small mesh layer. Rinse with clean water to eliminate any dirt or pollutants that may have accumulated during usual use. Rinse the sides of the lower filter holder as well.
- In the filter housing unit, replace the filter. Insert the new filter into the filter holder, rounded top-side up. Place the bottom filter holder beneath it. The flat bottom of the fabric filter should be covered by the mesh bottom of the lower filter holder. Snap the filter holder’s two edges together around the filter
- Advance the replacement clock by two months. The filter replacement unit’s replacement dial is situated on top of the handle. It’s roughly the size of your thumb and has numerals 1–12 written on it (each of which stands for the corresponding month). Turn the dial clockwise until the indicator shows month two ahead of the current month. Keurig will utilize this configuration to send an electronic reminder in two months. However, you must explicitly schedule the notification.
- Set the Keurig to notify you when it’s time to change the filters. Your Keurig can be programmed to remind you to replace the water filter every two months. You can activate the reaffirmation using the electronic menu if you adequately adjusted the replacement dial two months ahead. Select “Water Filter Reminder” from the “Settings” menu. Choose “Enable.” The menu on your Keurig machine may change somewhat according to the model and generation.
- Fill the Keurig reservoir with water after inserting the water filter device. Replace the filter unit in the Keurig’s water filter once it has been reassembled. When firmly placed into the reservoir’s bottom, the exterior side of the lower filter holder will snap into place. If the filter does not click into place, make sure the grooves on the bottom of the lower filter holder are correctly aligned with the raised plastic on the Keurig’s water reservoir floor.
Conclusion
To use filtered water in a Keurig Coffee maker is recommended as it helps to enhance the coffee flavor. There are many of them which already contains filters in it. So, one should make it sure to replace it at the right time before it prepares a coffee with worse taste. Thus, one should know the right location of the water filter which will surely help to prepare the right coffee with the filtered water!
That concludes our comprehensive guide to all you need to know about the Keurig water filter; perhaps, this has solved any of your questions.
